Slurry Pumps Manufacturers

JOLLY SERIES

• Designed for heavy duty slurry and/or acid applications.
• The JOLLY Series slurry pumps are custom built to customer specifications.
• The shaft is always supported above the baseplate by two bearings inside the base.
• The pump-motor coupling is an elastic joint or V-belt.
• The maximum length of the pump under the base can reach 4-5 meters (13-16 ft).
• Using a sleeve bushing as the sealing system, the JOLLY Series slurry pumps cannot run dry under a certain level.
• Capacities from 5 to 1500 m3/h (22 to 6,613 gpm).
• Maximum discharge pressure from 6 to 7 bar (88 to 103 psi).

MEC SERIES

• Designed for heavy duty slurry and/or acid applications.
• The MEC Series only has direct transmission by means of an elastic joint. There is always a metallic structure around the motor with a lifting eyebolt at the top.
• Lengths under the bases are standard and do not exceed 2 meters (7 ft).
• Using a sleeve bushing as the sealing system, the MEC Series slurry pumps cannot run dry under a certain level.
• Capacities from 5 to 1500 m3/h (22 to 6,613 gpm).
• Maximum available pressure from 6 to 7 bar (88 to 103 psi).

AUS SERIES

• Designed for heavy duty slurry and/or acid applications.
• The AUS Series slurry pumps can run dry since there is no mechanical seal.
• Mechanically speaking these slurry pumps are the same as the JOLLY series, but the maximum length of the AUS Series pump under the base seldom exceeds 2 meters (7 ft).
• Usually the fluid inlet is above the casing but in some versions it is also near the bottom (double sided impellers).
• The AUS Series slurry pumps can be installed inside or outside tanks.
• Capacities from 5 to 1500 m3/h (22 to 6,613 gpm).
• Maximum available pressure from 6 to 7 bar (88 to 103 psi).

AO/TI and AO/TD series

• Designed for heavy duty slurry and/or acid applications.
• These are end suction slurry pumps with single or double mechanical seals.
• Capacities from 1 to 1500 m3/h (5 to 6613 gpm).
• Usually maximum discharge pressure should not exceed 3 bar or 43 psi.

AO/AB SERIES

• Designed for slurries and/or acid applications.
• The heart of the PEMO product line, the AO/AB Series pumps are truly unique. Due to the side inlet, the maximum pressure the mechanical seal will see is the fluid inlet pressure, greatly increasing life of the seal.
• When pumping acid liquids, the shaft and the mechanical seal housing can be made of special alloys.
• Maximum particle size is 2 mm though this is dependent on the specific application.
• Capacities from 1 to 900 m3/h (5 to 3,968 gpm).
• Maximum discharge head is 90 m (295 ft) in the Hardalloy PEMO design.

• The PEMO submersible slurry pumps are designed for heavy duty slurry applications.
• High efficiency motor (class IE3) with power ranging from 1 to 100 hp, and speeds from 735 to 3,500 rpm (50 and 60 Hz).
• Standard capacities up to 700 m3/h (3,082 gpm).
• Maximum pressure up to 7 bar (103 psi).
• Double mechanical seals, silica carbide or widia wear rings, oil lubricated.
• Radial bearings, life lubricated and maintenance free, are made to deliver long-life.
• All PEMO Submersible slurry pumps are provided with thermal probe (for the control of motor temperature), and two oil level probe (for slurry leak detection inside the oil chamber).
• The Pemo Submersible slurry pumps all are sold with an electric device for the analysis of the signals from the thermal probes.
• Optional agitator, mechanical and/or hydraulic type.

AO/AB/DC SERIES (double stage versions)

• Designed for slurries and/or acid applications.
• The AO/AB/DC Series is the perfect solution for filter press feed or slurry transfer.
• When pumping acid liquids, the shaft and the mechanical seal housing can be made of special alloys.
• Maximum particle size is 1 mm, though this is dependent on the specific application.
• Capacities from 5 a 900 m3/h (22 to 2,645 gpm).
• The maximum head for some Hardalloy versions is 210 m/H2O.

SUITABLE FOR:

• Applications under head
• Abrasive liquids
• Acid liquids even with solids in suspension
• Operating temperature up to 90 °C

TYPES OF SEALING:

Mechanical seal with front rings double flushed or with permanent lubrication.

MINIMUM MAINTENANCE

Pump/motor coupling:

• By means of pulleys and V-belts
• By means of elastic coaxial joint

These are AO/AB slurry pumps but with two bodies installed on the same shaft so that, working in series, high pressures (up to 12/15 atm) can be obtained, particularly suitable for feeding filters for high pressing.

The Triple Stage PEMO PUMPS, are used with pressures up to 24 bar, have been developed to work 24 h / day in the Ceramic Industry to power Spray Dryers, and today they are also successfully used for new applications of filter presses (bentonite, kaolin , sewage, etc.).